Advantech TPC-1261H User Manual

TPC-1261HGX3 LX800 Touch Panel Computer with 12.1" SVGA TFT LCDUser Manual

TPC-1261H User Manual xFigure F.2:Install Wizard - 1 ... 84Figure F.3:Install Wizard - 2 ...

TPC-1261H User Manual 90Figure F.11: Advanced Calibration -2Figure F.12: Plot Calibration Data

91 Appendix F DrawThis is to test the touchscreen operation. Its display shows touch loca-tion.Figure F.13: Draw Click “menu” and then click “clear

TPC-1261H User Manual 92Figure F.14: Clear ScreenOptionThis option is to set the operation mode and beep sounds if the beep sound is enabled. The ope

93 Appendix F Figure F.15: Option

TPC-1261H User Manual 94

2 APPENDIX GFuse Specifications

TPC-1261H User Manual 96Appendix G Fuse SpecificationsG.1 Fuse SpecificationsRating: 250 V AC, 5 ASize: 5 x 20 mmG.2 Fuse ReplacementStep 1: Remove

2CHAPTER 1General InformationThis chapter gives background infor-mation on TPC-1261H..Sections include:• Introduction• Specifications• I/O Ports Ar

TPC-1261H User Manual 2Chapter 1 General Information1.1 IntroductionThe TPC-1261H touch panel computer is a state-of-the-art HMI (Human Machine Inte

3 Chapter 1 1.2 Specifications1.2.1 System Kernel• CPU: GeodeLink Control Processor LX800 500MHz• BIOS: Award 512KB flash memory• South Bridge: G

TPC-1261H User Manual 4Environment• Operating Temperature: 0 ~ 50° C (32 ~ 122° F)• Storage Temperature: -20 ~ 60° C (-4 ~ 140° F)• Humidity: 40° C

5 Chapter 1 1.5 Power• Input Voltage: 18 - 32VDC (the fuse will become an open circuit if the input level exceeds 33 VDC)• Typical: [email protected].

TPC-1261H User Manual 6Figure 1.2: Panel Mounting1.8 Dimensions and Cutout• Weight: 4.1 kg (without HDD)• Dimensions: 311 x 237 x 58 mm (W x H x D)

7 Chapter 1 Figure 1.3: Dimensions

TPC-1261H User Manual 8

2CHAPTER 2System SetupThis chapter provides a brief explana-tion for operating TPC-1261H.

TPC-1261H User Manual iiCopyrightThe documentation and the software included with this product are copy-righted 2004 by Advantech Co., Ltd. All rights

TPC-1261H User Manual 10Chapter 2 System SetupYou can easily get TPC-1261H started by following the below steps.• Step 1: Unpack the TPC-1261H packa

11 Chapter 2 • Step 2: Install a CompactFlash card containing Windows CE, embed-ded Windows XP or another operating system.Figure 2.2: Install Compa

TPC-1261H User Manual 12• Step 4: Plug the power lines into the system power receptor.• Step 5: Push the power button to power on the system (figur

2CHAPTER 3System Engine

TPC-1261H User Manual 14Chapter 3 System EngineTable 3.1: Mainboard Connectors & Jumper SettingsLabel Function DescriptionCN2 LCD POWER LCD INVE

15 Chapter 3 Figure 3.1: Main Board Connectors - 1Figure 3.2: Main Board Connectors - 2

TPC-1261H User Manual 16

2CHAPTER 4Software ConfigurationSections include:• VGA Driver Installation• Advantech COM Installation• Entertainment Encryption/ D

TPC-1261H User Manual 18Chapter 4 Software ConfigurationA support CD-ROM for TPC-1261H is available and along with the product. There are related u

19 Chapter 4 Figure 4.2: Update DriverStep 3: Then follow the update wizard processures.Figure 4.3: Update Wizard-1

iiiProduct Warranty (1 year)Advantech warrants to you, the original purchaser, that each of its prod-ucts will be free from defects in materials and w

TPC-1261H User Manual 20Figure 4.4: Update Wizard-2Figure 4.5: Update Wizard-3

21 Chapter 4 Figure 4.6: Update Wizard-4Figure 4.7: Update Wizard-5

TPC-1261H User Manual 22Figure 4.8: Update Wizard-6Step 4: After you successfully update the driver, you can see the VGA successfully installed from t

23 Chapter 4 4.2 Advantech COM Driver InstallTwo com ports named COM3 and COM4 on TPC-1261H are Advantech Special com port. Please follow the steps

TPC-1261H User Manual 24Figure 4.12: PCI ICOM Installation - 2Step 3: Then, go to “Device Manager” to update the driver. Click “?PCI Serial Port” and

25 Chapter 4 Figure 4.14: Update Driver - 1Step 4: Follow the hardware update wizard as the figures below. Figure 4.15: Update Driver - 2

TPC-1261H User Manual 26Figure 4.16: Update Driver - 3Step 5: Complete the PCI-1602 Series Slave Bridge installation.Figure 4.17: Slave Bridge Install

27 Chapter 4 Step 6: Then, go to “Device Manager”. You can find “Advantech PCI-1602 Series Slave Bridge” is on the list.Figure 4.18: PCI-1602 Device

TPC-1261H User Manual 28Figure 4.19: PCI Serial port Device ManagerFigure 4.20: Update Driver - 1

29 Chapter 4 Step 8: Follow the hardware update wizard as the figures below.Figure 4.21: Update Driver - 2Figure 4.22: Update Driver - 3

TPC-1261H User Manual ivCEThis product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We r

TPC-1261H User Manual 30Step 9: Complete the Advantech PCI-1602 Series Master Bridge installa-tion.Figure 4.23: PCI-1602 Master InstallationStep 10: T

31 Chapter 4 Figure 4.25: PCI Serial Port Installation - 2 Figure 4.26: PCI Serial Port Installation - 3

TPC-1261H User Manual 32Figure 4.27: PCI Serial Port Installation - 4 Figure 4.28: PCI Serial Port Installation - 5

33 Chapter 4 Figure 4.29: PCI Serial Port Installation - 6Figure 4.30: PCI Serial Port Installation - 7

TPC-1261H User Manual 34Step 11: After the steps are done, the software for the com3 and com4 is successfully installed. Go to “Device Manager” and f

35 Chapter 4 Step 2: Following the install shield wizard to finish the setup. Figure 4.33: Install Wizard - 1 Figure 4.34: Install Wizard - 2

TPC-1261H User Manual 36Figure 4.35: Install Wizard - 3Step 4: The driver is successfully installed. You can check via “Device Manager” as the below.

2CHAPTER 5Features in Windows XP Embedded Sections include:• EWF• HORM• Advantech Utilities

TPC-1261H User Manual 38Chapter 5 Features in Windows XP EmbeddedTPC-1261H supports the embedded Windows platform. This section out-lines the import

39 Chapter 5 5.2 HORMHORM stands for Hibernate Once Resume Many. In HORM environ-ment, a single hibernation file is used to boot the system repeated

vPacking ListBefore setting up the system, check that the items listed below are included and in good condition. If any item does not accord with the

TPC-1261H User Manual 405.3.1 Version InformationStart menu-> All Programs -> AdvantechThis states the current XPE runtime information including

41 Chapter 5

TPC-1261H User Manual 42

2 APPENDIX ASerial Port Settings

TPC-1261H User Manual 44Appendix A Serial Port SettingsA.1 COM1/ COM2/ COM3 Connector Definition Pin Signal1NDCD2NRX3NTX4NDTR5GND6NDSR7NRTS8NCTS9NR

45 Appendix A A.2 COM4 SettingThe serial port COM4 on the TPC-1570H is adjustable. It can be set to RS-232, RS-422 or RS-485. This port is designe

TPC-1261H User Manual 46PIN RS-232 RS-422 RS-4851 NDCD TX- D-2NRX TX+ D+3NTX RX+4 NDTR RX-5 GND GND GND6 NDSR7NRTS8NCTS9NRI

2 APPENDIX BWatchdog Timer Programming

TPC-1261H User Manual 48Appendix B Watchdog Timer ProgrammingB.1 OverviewThe TPC-1261H watchdog timer can be used to monitor system so

49 Chapter B B.2 Watchdog Timer ProgrammingThe I/O port address of the watchdog timer is 2E(hex) and 2F(hex), 2E (hex) is the address port. 2F(hex)

TPC-1261H User Manual vi13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.14. If on

TPC-1261H User Manual 50Table B.1: Watchdog Timer RegistersAddress of register (2E)Attribute DescriptionRead/Write Value (2F) anddescription87 (hex) -

51 Chapter B B.3 Example Programs1. Enable watchdog timer and set 10 sec. as timeout interval;------------------------------------------------------

TPC-1261H User Manual 52Out dx,alInc dxMov al,10Out dx,al;-----------------------------------------------------------Dec dx ; lock W83627HFMov al,0aah

53 Chapter B Out dx,alInc dxIn al,dxOr al,08hOut dx,al;-----------------------------------------------------------Dec dx ; Set timeout interval as 5

TPC-1261H User Manual 54Mov al,30hOut dx,alInc dxMov al,01hOut dx,al;-----------------------------------------------------------Dec dx ; Enable watchd

55 Chapter B Dec dx ; Enable the function of watchdog timerMov al,30hOut dx,alInc dxMov al,01hOut dx,al;---------------------------------------------

TPC-1261H User Manual 56;-----------------------------------------------------------Dec dx ; Enable the function of watchdog timerMov al,30hOut dx,alI

2 APPENDIX CWatchdog TimerProgramming on WinCE

TPC-1261H User Manual 58Appendix C Watchdog Timer Program-ming on WinCEThere is a built-in watchdog timer in Windows CE 4.2 for TPC-1261H. You can ac

59 Appendix C C.1.1 Parameters• hDevice [in] Handle to the device that is to perform the operation. Call the Cre-ateFile function to obtain a device

vii Table of ContentsContentsChapter 1 General Information ... 21.1 Introduction ...

TPC-1261H User Manual 60C.2 How to Use the Control CodeThere are 6 control codes for the operation codes in the WDT driver.C.2.1 IOCTL _WDT_ENABLE:En

61 Appendix C C.2.4 IOCTL_WDT_GETTIMEOUT:Gets the Watchdog time setting.lpInBuffer: unused.nInBufferSize: unused.lpOutBuffer: The DWORD points to you

TPC-1261H User Manual 62C.3 Examples#define WDT_CODE(ID) CTL_CODE(FILE_DEVICE_UNKNOWN,ID, METHOD_BUFFERED, FILE_ANY_ACCESS)#define IOCTL_WDT_ENABLE W

63 Appendix C // Set the Watchdog Timer as 10 seconds. Number 2 means 10 seconds.DeviceIoControl(m_hWDT, IOCTL_WDT_SET_TIMEOUT, &nIndex,sizeof(nI

TPC-1261H User Manual 64

2 APPENDIX DAccessory Kit Assembly ProcedureThis appendix shows how to connect to a CD-ROM via the CompactFlash slot.:

TPC-1261H User Manual 66Appendix D Accessory Kit Assembly ProcedureD.1 CompactFlash to IDE Transfer KitPlease follow this assembly procedure to use

67 Appendix D 2. Insert the adapter board into the CompactFlash slot.Figure D.3: CompactFlash SlotFigure D.4: Insert the Adapter Board into the CF sl

TPC-1261H User Manual 68Connect the CD-ROM to the adapter board via the IDE cable and then connect the external power line to the CD-ROM.Figure D.6: C

2 APPENDIX EHDD Kit Assembly

TPC-1261H User Manual viiiFigure 4.14:Update Driver - 1 ... 25Figure 4.15:Update Driver - 2 ...

TPC-1261H User Manual 70Appendix E HDD Kit AssemblyTPC-1261H provides two way to assemble the HDD into the system. The ruggized HDD kit is to resist

71 Appendix E Figure E.2: Required Parts

TPC-1261H User Manual 722. Place the base bracket on the rear case and carefully pull out the FPC cable through the hole of the bracket.Figure E.3: Op

73 Appendix E 4. Carefully connect the FPC cable to the HDD and then put the HDD insultor on the HDD.Figure E.5: Connectting the FPC with the HDDFigu

TPC-1261H User Manual 745. Fasten the HDD holder with the HDD and HDD insulator. Please turn over the HDD holder and fasten them with 4 screws.Figur

75 Appendix E 6. Mount the HDD cushions with the HDD holder.Figure E.9: Mounting the cushions - 1Figure E.10: Mounting the cushions - 2

TPC-1261H User Manual 767. Place the HDD holder on the rear cover of the system and then fas-ten the holder with the system by four screws. Then, the

77 Appendix E Figure E.13: Fastening the HDD holderE.2 Internal HDD Kit AssemblyPlease follow the steps to assemble the internal HDD kit.1. Remove t

TPC-1261H User Manual 782. There are four rubber screw casings, and four screws. Places the screws into their casingsFigure E.15: Placing a screw int

79 Appendix E 4. Connect the FPC cable to the HDDFigure E.17: Connecting the FPC cable5. Put the HDD into the hole of the rear case. Figure E.18: Ins

ix Table of ContentsC.2.2 IOCTL _WDT_DISABLE: ... 60C.2.3 IOCTL_WDT_STROBE: ...

TPC-1261H User Manual 806. Lay the HDD insulator in right direction.Figure E.19: Laying in the HDD insulator7. Place the default HDD cover on the syst

81 Appendix E 8. Fasten the default HDD cover with the system.Figure E.21: Re-fastening the cover - 1Figure E.22: Re-fastening the cover - 2

TPC-1261H User Manual 829. Place the bracket of PCI/104 on the slot and fasten it into place.Figure E.23: Fastening the PCI/104 bracket - 1Figure E.24

2 APPENDIX FTouchscreen Installation & ConfigurationThis appendix demonstrates how to install the PenMount touchscreen

TPC-1261H User Manual 84Appendix F Touchscreen Installation & ConfigurationF.1 Driver InstallationPlease insert the x86 TPC series support CD an

85 Appendix F Figure F.3: Install Wizard - 2Figure F.4: Install Wizard - 3

TPC-1261H User Manual 86F.2 Uninstall the DriverPlease go to Settings and then select Control Panel. Please click Add/Remove Programs. Figure F.5: U

87 Appendix F F.3 Touchscreen CalibrationThe “PM”, the icon of the PenMount Control Panel, is in the menu bar after the touchscreen installation. P

TPC-1261H User Manual 88Figure F.8: Standard Calibration -2Figure F.9: Standard Calibration -3

89 Appendix F Advanced Calibration is for the aged touchscreens by using 4, 9, 16 or 25 points to calibrate touch panel.Figure F.10: Advanced Calibra