Advantech AIMB-760 User Manual Page 1

ACP-40104U-High 15-slot Rackmount Chassis with Visible & Audible Alarm NotificationUser Manual

ACP-4010 User Manual x3.4 Cleaning the Filters ... 20Figure 3.6 Replacing the filters...

xiB.2 Motherboard Options ... 35Table B.3 ATX Motherboard Options ... 35

ACP-4010 User Manual xii

1CHAPTERGeneral Information

ACP-4010 User Manual 2Chapter 1 General Information1.1 Introduction ACP-4010 is a 4U-high rackmount industrial computer chassis for high-performance

3 Chapter 1 General Information1.3 Power Supply Options Table 1.1: Power supply optionsModel NamePS-300ATX-ZBE RPS-300ATX-ZEWatt300 W max. (ATX, PFC)

ACP-4010 User Manual 41.4 Environment Specifications Table 1.2: Environment specificationsEnvironment Operating Non-operatingTemperature 0 to 40°C (3

5 Chapter 1 General Information1.5 Dimension Diagram Figure 1.1: Dimension diagramunit:mm[inch]

ACP-4010 User Manual 6

2CHAPTERSystem Setup

ACP-4010 User Manual iiCopyrightThis documentation and the software included with this product have been copyrighted by Advantech Co., Ltd. in Februar

ACP-4010 User Manual 8Chapter 2 System SetupThe following procedures instruct users to install a backplane/mother-board, add-on cards and disk drives

9 Chapter 2 System Setup2.2 Installing the Backplane or Motherboard ACP-4010 supports either; an up to 15-slot backplane or ATX m

ACP-4010 User Manual 10 Figure 2.2: Yellow label indicating copper stub locations Figure 2.3: Installing the backplaneAIMB-744Be careful to screw the

11 Chapter 2 System SetupFigure 2.4: Installing a motherboard2.3 Installing CPU Card or Add-on CardACP-4010 supports up to 15 cards. To install a CP

ACP-4010 User Manual 126. For the PICMG1.0 Backplane, connect the orange-white wire from the connector ‘CN20’ on the CPU card to the connector ‘HCN1’o

13 Chapter 2 System Setup Figure 2.6: Installing rubber cushions and hold-down clamp2.5 Installing Disk DrivesThe APC-4010 supports two 5.25” disk dr

ACP-4010 User Manual 14Figure 2.7: Installing 3.5” HDD, FDD or optical disk drive2.6 Attaching the Ears and HandlesThere is a pair of ears and hand

3CHAPTEROperation

ACP-4010 User Manual 16Chapter 3 Operation3.1 The Front Panel of ACP-4010The front panel features the lockable door and six LED indicators. The user c

17 Chapter 3 Operation3.1.1 Switch, Button and I/O InterfacesMomentary Power switch: Press this switch to turn the system power on or off. Please use

iiiSafety Instructions1. Read these safety instructions carefully.2. Keep this user manual for later reference.3. Disconnect this equipment from AC ou

ACP-4010 User Manual 18When the system power is on, the power LED is always Green.When the power LED is RED, it indicates a redundant power supply mod

19 Chapter 3 OperationFigure 3.4: Rear panel of motherboard versionThere is a ground screw with a washer located on the lower right of the rear panel

ACP-4010 User Manual 20Figure 3.5: Replacing the cooling fan3.4 Cleaning the FiltersThe filter functions to block dust or particles from the work envi

21 Chapter 3 Operation3.5 Replacing the Power SupplyThe ACP-4010 supports either a single PS/2 or a redundant power supply. To replace the power su

ACP-4010 User Manual 224. Slide the power supply module inward until it locks into the right position.5. Secure the screw and replace the handle. Then

4CHAPTERAlarm Module

ACP-4010 User Manual 24Chapter 4 Alarm ModuleThe alarm board is located behind the cooling fan near the middle section. The alarm board makes an audi

25 Chapter 4 Alarm Module• One ‘voltage signal’ connector (connect from the backplane / motherboard, supporting six voltages: ±12 V, ±5 V, +3.3 V, and

ACP-4010 User Manual 26Table 4.6: CN18, Output connector to LED boardPin 1 GND Pin 9 Temperature GoodPin 2 +5 V signal Pin 10 Temperature Fail Pin 3 +

27 Chapter 4 Alarm Module4.2.2 Switch SettingsThe alarm board is designed to connect with up to 7 fans. Users can set the fan number by adjusting the

ACP-4010 User Manual ive The equipment has been dropped and damaged.f The equipment has obvious signs of breakage.16. THE COMPUTER IS PROVIDED WITH CD

ACP-4010 User Manual 28Please refer to Figure 4.3 for a diagram of the thermal sensor module lay-out. Figure 4.3: Thermal sensor moduleUsers can set u

AAPPENDIXExploded Diagram & Parts List

ACP-4010 User Manual 30Appendix A Exploded Diagram & Parts ListA.1 Exploded Diagram and Parts List

31 Appendix A 9 Fan bracket 19 CD-ROM cover 29 Switch bracket10 12cm fan 20 FDD cover 30Disk mounting bracketTable A.1: Parts List

ACP-4010 User Manual 32

BAPPENDIXBackplane & Mother-board Options

ACP-4010 User Manual 34Appendix B Backplane and Motherboard OptionsB.1 Backplane OptionsACP-4010 supports a variety of PICMG 1.3 / 1.0 backplanes. Us

35 Appendix BB.2 Motherboard OptionsACP-4010 supports a variety of Advantech ATX motherboards as below. Users can contact a local sales representative

ACP-4010 User Manual 36

vA Message to the Customer Advantech customer servicesEach and every Advantech product is built to the

ACP-4010 User Manual viProduct warrantyAdvantech warrants to you, the original purchaser, that each of its prod-ucts will be free from defects in mate

viiInitial Inspection When you open the carton, please make sure that the following materials have been shipped:1. ACP-40

ACP-4010 User Manual viii

ixContentsChapter 1 General Information ...........21.1 Introduction ..............